Why Learning Plumbing Basics is Vital for Bathtub Installation
Why Learning Plumbing Basics is Vital for Bathtub Installation
Blog Article
Do you find yourself searching for information about A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough task. If the old bathtub is easily available, the task can move immediately; if you have to open up a wall surface to remove the old bathtub and also position the new bathtub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly need an assistant to vacate the old tub as well as embeded in the new one. See to it you have qualified yourself for the work and also are comfortable attempting it. As opposed to working with a specialist to take control of a halfway-completed task, it is far better to consider utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will assist you mount a brand-new tub in your washroom if you have actually currently gotten a brand-new tub and don't need to change the plan of your previous water system pipes.
Your tools and product list ought to comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of removing the existing faucets can be rather problematic because of the restricted gain access to that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipes. When the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making certain that the washers remain in location between the tap and also the sink. Secure the faucet in position with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type must be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Utilizing the two wood boards under its feet, place the tub in the required setting. The wood boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the tub till the level reviews level.
To set up taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression join; then do the exact same for the other faucet.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bathtub and also examine the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also securing around the tub should wait till the tub has actually been used at the very least when as this will certainly resolve it right into its final placement.
Preparing for the Installment
First of all, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you use every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and also cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in use. The sealant can break relatively early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily available on the market. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that piece of content was mandatory. Do you know about anybody else who is interested in the topic? Please feel free to promote it. I love reading our article about How to Install a Bathtub.
Drain woes? Connect. Report this page